Gto Pro 3000 Troubleshooting
Posted onby admin
- Gto Pro 3000 Troubleshooting Hp
- Mule Gate Opener Troubleshooting
- Gto Pro 3000 Troubleshooting Pool Pump
- Gto Pro 3000 Troubleshooting Washer
- Gto Pro 2000 Troubleshooting
- Gto Pro 3000 Troubleshooting Garage Door Opener
GTO 3000XLS gate opener troubleshooting. Disconnect the push button, keypad, intercom keypad, or any other accessory wired to this terminal. Try the remote. If the remote works, then the problem is the accessory. Disconnect the loop detector, photo beam, or any other accessory wired to this terminal. View and Download GTO 3000XLS installation manual online. 3000XLS gate opener pdf manual download. Also for: 32000xls.
GTO gate opener troubleshooting is often performed by homeowners as some of the problems are really simple. Even if it is your first attempt to fix the gate opener, it may take you less than half an hour, if you follow the instructions from the tables below.
GTO 3000XLS gate opener troubleshooting
| SYMPTOM | DIAGNOSIS | CHECK: |
| 1 short beep upon power up | Circuit Board Powered Up& Ready | • Normal Operation |
| 1 short beep upon activation | Blown Fuse Low or Bad Battery Loose Battery Connection | • Fuse • Battery Under Load • Battery Harness Connections |
| Continuous Uninterrupted Alarm | Circuit Board Senses an Obstruction | • Path of Gate • Gate for Level and Plumb • Stall Force Adjustment • Disconnect Safety Devices • Rev Counter |
| 1 beep with 10 seconds off | Low Battery Condition | • Fuses • Battery Harness Connections • Battery Under Load |
| 1 beep then 2 beeps | Master Motor Terminals Shorted | • Connections to Master Inputs • Master Arm Power Cable • Motor • Circuit Board |
| 1 beep then 3 beeps | Second Motor Terminals Shorted | |
| 1 beep with 2 seconds off | Master Arm Limit Switch Error | • Connections to Master Inputs • Master Arm Power Cable |
| 2 beeps with 2 seconds off | Second Arm Limit Switch Error | |
| 3 beeps with 2 seconds off | Master Arm Rev Counter Error | • Connections to Master Inputs • Master Arm Power Cable • Rev Counter |
| 4 beeps with 2 seconds off | Second Arm Rev Counter Error | |
| Status (clear)l blink | Cycle Terminal Shorted | • Disconnect the push button, keypad, intercom keypad, or any other accessory wired to this terminal. • Try the remote. If the remote works, then the problem is the accessory. |
| Status (clear) 2 blinks | Safety Terminal Shorted | • Disconnect the loop detector, photo beam, or any other accessory wired to this terminal. • Try the remote. If the remote works, the problem is the accessory. |
| Status (clear) 3 blinks | Exit Terminal Shorted | • Disconnect exit wand, loop detector, photo beam, or any other accessory wired to this terminal. • Try remote. If the remote works, the problem is the accessory. |
| Status (clear) 4 blinks | Shadow Terminal Shorted | • Disconnect the loop detector, photo beam, or any other accessory wired to this terminal. • Try remote. If the remote works, the problem is the accessory. |
| Status (clear) 5 blinks | Close Edge Terminal Shorted | • Disconnect the edge sensor, photo beam, or any other accessory wired to this terminal. • Try the remote. If the remote works, the problem is the accessory. |
| Status (clear) 6 blinks | Open Edge Terminal Shorted | • Disconnect edge sensor, photo beam, or any other accessory wired to this terminal. • Try the remote. If the remote works, the problem is the accessory. |
| RF (yellow) Flickers | Receiving 318 MHz RF | • Normal operation when remote or wireless keypad is used. |
| RF (yellow)OFF | No 318 MHz RF Received | • Battery in Remote • Program Remote • Antenna Receiver Connections • Antenna Receiver |
| Power (green) ON | AC or Solar Power Present | • Normal Operation |
GTO GPX-SL25 gate opener troubleshooting
| SYMPTOMS | CAUSES | CORRECTIVE ACTION |
| Unit clicks but does not operate | • Gate binding or not sliding freely • Motor pulling too many amps • Motor open circuit | • Check replace fuse(s) • Check battery connections at battery and control board • Check motor lead connection at the control board • If this is single gate operator, make sure that DIP 3 is set for single. Turn unit off them back on. • Check battery for dead cell (load test) |
| Unit not responding (Red status LED flashing) Unit works (Green status LED off) | • Low battery (less than 12 vdc) • Unit not charging • Adverse solar conditions | • Test transformer output • Test solar panels |
| Unit not responding (Red status LED on) | • Transmitter not programmed correctly • Faulty accessory device | • Reprogram your transmitter • Remove accessories. If unit functions - you likely have a accessory issue • Momentarily connect the WHT & GRN on accessory terminal block. If unit functions, then you may have a faulty receiver, receiver circuit or remote transmitter |
| Unit not responding (Status LED off) | • Unit may not be charging | • Cycle power switch • Check battery voltage • Check receiver wiring • Check transformer and wiring • Check solar panel and/or solar conditions |
| Unit stopping and reversing direction during operation | • Improper obstruction setting | • Adjust gate. The gate is binding or not sliding freely • Adjust the obstruction and the inertia POT as needed • Check and/or remove accessory and test for proper operation |
Gto Pro 3000 Troubleshooting Hp
GTO Mighty Mule FM200 gate opener troubleshooting
| Symptom | Diagnosis | Check: |
| 1 or more short beeps upon power up | Circuit Board Powered Up & Ready | • Normal Operation |
| Continuous beep after power-up | Unit has learned new transmitter code, releasing the transmitter button will shut off alarm. Unit has entered 'LEARN LIMIT' mode. Releasing the transmitter will turn off alarm. | • Normal Operation |
| Rapid beeping | Circuit Board Senses an Obstruction | • Path of Gate • Gate for Level and Plumb • Stall Force Adjustment • Disconnect Safety Devices |
| 1 beep with 20 seconds off | Low Battery Condition | • Transformer or Solar Panel Voltage • Battery Harness Connections • Battery Under Load |
| 2 beeps every 2 seconds | Position sensor is short circuit. | • Arm Power Cable for Damage |
| 1 beep with 2 seconds off | Arm Limit Switch Error | • Connections to Inputs • Arm Power Cable for Damage |
| 1 beep when attempting to run the gate | Blown fuse Battery is low or damaged Loose Connection | • Check and replace fuse • Test battery voltage • Check all connections |
| Power (green) ON | AC or Solar Power Present | Normal Operation |
| Power (green) OFF | No AC or Solar Power | Transformer: • Breaker or GFI • Power at AC outlet. • Output of Transformer. • Voltage on wire at 18 VAC Input Solar: • Solar Panel Wires Reversed • Weather • Solar Panel Placement • Output of Solar Panel • Voltage on wire at Solar Input |
Mule Gate Opener Troubleshooting
Gto Pro 3000 Troubleshooting Pool Pump
GTO Pro SL-1000 gate opener troubleshooting
| Problems | Cause/Solutions |
| Maintenance: | • On all gates weighing 250 lb. or more, routinely grease the ball bearing rollers at least 4 times a year; grease more frequently if the gates are near a coastal area. • Keep a few mothballs in the control box to discourage insects from entering it and damaging the control board. • Have your gate operator tested monthly and serviced regularly by an experienced technician. The gate MUST stop and reverse on contact with an obstruction or when an object activates the non-contact sensors. If these functions are observed to operate improperly, discontinue use and have operator serviced immediately. |
| The operator has a 12 Vdc motor with mechanical limit switches. | • To test the motor, put a voltmeter on DC and place the meter leads on the wire connections inside the plastic cover above the switches. The reading should be at least 11.5V when the system is active. • To test the switc hes, put the meter on “ohms.” Place the leads on each of the wires on the switch. Y ou should have an open circuit. Click the switch and you should have .2 ohms. Do this for both switches. • To test the cable, put the meter on ohms. At one end of the cable place the lead on the green wire, and on the other end of the cable place the lead on the green wire and the other wires. This should show a maximum of 1.0 ohms on the green wire and nothing on the other wires. Test each wire as you have above. If all have the proper readings, then this is not the problem. • Note: Inspect the cable for any signs of any punctures because wires inside the PVC jacket can be shorted and the cable will still show proper ohms. |
| The control board: | This is a micro processor board. The power that runs the gate is from the battery and recharged, through the board only, by a 18 volt 40 VA. (2.9 A) transformer. There is one (1) green and one (1) red LED (light emitting diode) on the control board. They are for a quick reference only. All readings must be measured by a voltmeter! The red light serves two purposes. The first is to aid in storing the personal transmitter code. The second is to show the condition of the battery. If it is flashing, see the following section the battery. The normal state of this light is on, but dim. If the red LED is flashing it means that the system may have reached low voltage lockout; the unit does not have enough voltage to operate the system. One of the following problems may exist: • Broken or spliced wires from the transformer or solar panel to the control board. • A transformer or solar panel that has no output voltage. • Incorrect number of solar panels, or solar panels not properly hooked up. The green light serves as a quick visual indication that the control board is receiving power from the transformer. |
| The transformer: | Two things can cause failure: the first is shorting the leads during the installation, or letting the strands touch at the terminal on the control board. The second is a static charge (generally associated with a lightning storm or power outage); use of a surge protector will help. |
| Testing the battery: | This is a 12 volt 7 Ah battery. The proper way to test this is to perform a load test. Place the voltmeter on D.C.; put the red probe on the (+) positive terminal and place the black probe on (-) negative terminal. Then activate the unit and watch the voltmeter. The drop should not be more than 1 volt. |
| Remote control range: | This will vary at each installation, but generally varies from 50 ft. to 100 ft. • Make sure that the receiver is located above metal fences. • Moving the receiver even a few inches can change the range of operation. • Move the receiver as far from the motor as possible to avoid the chance of electrical interference. • Check or change the battery in the transmitter. |
Gto Pro 3000 Troubleshooting Washer
GTO PRO SW-6101 gate opener troubleshooting
| Symptom | Diagnosis/Check |
| 1. If the PWR OK light will not come on: | A. Check the operator for inbound power. B. The operator is in “learn” mode. |
| 2. If the unit does not function: | A. Check the operator for inbound power. B. Make sure the ON/OFF switch is in the ON position. C. Control board may be damaged; call the GTO Service Department. |
| 3. If the control board lights are on but the unit will not operate: | A. Press the reset button on the motor. B. If you are using the transmitter to open the gate, jumper the CYCLE terminal. If the unit operates, the transmitter batteries may be discharged. Install fresh batteries in the transmitter. If problem persists, the receiver may be damaged. Call the GTO Service Department. C. Disconnect the accessories from the control board and jumper the CYCLE terminal. If the unit operates; then reconnect each accessory and test each; one at a time. |
| 4. If the gate starts: then stops or reverses: | A. The transmitter button is being held too long. B. If using a loop entry or exit, make sure the wires are connected to the correct terminal. C. The gate operator may have been improperly installed. D. The gate hinges are worn. E. The gate is not level. F. The obstruction level setting is too low. |
| 5. If the gate opens but will not close: | A. The auto-close timer (TYIR. OFF/ON DIP switch) is OFF. B. An input (e.g., loop relay, push button, etc.) may be stuck. C. Limit switch may be defective. |
| 6. If the thermal overload button constantly trips (i.e., 'pops out'): | A. Motor current may be excessive; call the GTO Service Department. B. Check wire connections. C. The gate has cycled too many times for the ambient temperature. |
Gto Pro 2000 Troubleshooting
GTO Access Systems is a US manufacturer of turnkey access control system solutions based in Tallahassee, FL. The company established in 1987 now sells products under two brands: Mighty Mule (designed for do-it-yourselfers) and Linear Pro Access.
Gto Pro 3000 Troubleshooting Garage Door Opener
GTO pro 2000 gate opener troubleshooting
| Problem | Cause | Solution |
|---|---|---|
| VISUAL INDICATORS | Power LED (Green) | ON: AC power or Solar power is present |
| OFF: There is no input power | ||
| Status LED (Yellow): (while unit is running this LED will be OFF) | Rapid blinking in random pattern: GTO’s transmitter 318 MHz signal is detected | |
| Continuously ON: Battery is in fast charge mode | ||
| 1 Blink every 2 seconds: Battery is in float charge mode (battery is fully charged) | ||
| OFF: Switch is in the OFF position or there is no input power for at least 60 seconds | ||
| AUDIBLE INDICATORS (ALARM/BUZZER) | Beeps upon power up | This is normal self test when the unit is turned on. |
| Continuous beep after power up | Unit has learned new transmitter code, releasing the transmitter button will shut off the alarm | |
| Rapid beeping | Unit has encountered two (2) obstructions without reaching either limit. (Power cycle to reset the alarm) | |
| Transmitter will not operate the gate | ||
| Alarm will automatically shut off after 5 minutes; gate will remain disabled until control box is restarted | ||
| 1 beep every 20 seconds | Low battery is detected | |
| 1 beep every 2 second | Position sensor is open circuit. Call GTO Service department | |
| 2 beeps every 2 second | Position sensor is short circuit. Call GTO Service department | |
| 1 or more beeps when attempting to activate the opener | Blown fuse | |
| Battery is extremely low or damaged | ||
| Loose connection from battery to circuit board | ||
| IF THE GATE STOPS AND REVERSES DIRECTION | Check the gate for binding or hinge damage | |
| Adjust stall force if necessary | ||
| Check the position of the mounting brackets and readjust or tighten if necessary |
GTO/PRO SW3000XL and SW3200XL replacement parts and replacement pieces for GTO SW 3000XL and SW 3200XL
| ||||||||||||||||||||||||||||||||